- Clamping unit/collar manufactured from ferritic stainless steel AISI 430 Ti
- 50mm – 150mm: M8 zinc plated socket cap screw and nut (6mm Allen Drive)
- 200mm: M10 zinc plated socket cap screw and nut (8mm Allen Drive)
- EPDM synthetic rubber sealing ring
- Block tightening provides visible torque control
- Pressure rated up to 0.5 bar unrestrained
- Quick Fitting
- Suitable for re-use
- Conforms to the requirements of BS EN 877
-
Above Ground Stainless Steel (Grade 430ti) Coupling. -
Single-piece casting manufactured from Ductile Iron BS EN 1563- Two EPDM sealing gaskets
- Uses the same grub-screw continuity system as proven on our Ductile Iron Couplings
- Meets Hydrostatic test pressures
- Couplings in 2-part epoxy finish to match the applicable system
- Suitable for re-use (Gasket should be checked before re-installation for damage/distortion and replaced if necessary)
-
Single-piece casting manufactured from Ductile Iron BS EN 1563- Two EPDM sealing gaskets
- Uses the same grub-screw continuity system as proven on our Ductile Iron Couplings
- Meets Hydrostatic test pressures
- Couplings in 2-part epoxy finish to match the applicable system
- Suitable for re-use (Gasket should be checked before re-installation for damage/distortion and replaced if necessary)
-
Below Ground Puddle Flange finished externally in a two part grey epoxy coating. Code number(s) for available products are: HD4078, HD6078, HD8078, HD10078 & HD12078 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. Bolt on flange is supplied in two halves with stainless steel nuts and bolts. Designed to be bedded on "Denso" tape or similar, wrapped around the pipe to provide a watertight seal. -
Below Ground plain grating. Code number(s) for available products are: HD8077 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Above Ground Pipe Taper finished externally in a two part red epoxy coating. For more specifications please see the table below. Code number(s) for available products are: HS3046, HS4046, HS4047, HS6046, HS6047, HS6048, HS8046, HS8047, HS10046, HS10047, HS10048, HS12046, HS12047 & HS12048 Fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Below Ground Pipe Taper finished externally in a two part grey epoxy coating. Code number(s) for available products are: HD6048, HD8046, HD8047, HD10046, HD10047, HD10048, HD12046, HD12047 & HD12048 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Above Ground Offset finished externally in a two part red epoxy coating. For more specifications please see the table below. Code number(s) for available products are: HS4044, HS2045, HS3045, HS4045 Fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Above Ground Manifold Connector finished externally in a two part red epoxy coating and fully compliant with BS EN 877:1999 + A1:2006. For more specifications please see the table below. Code number(s) for available products are: HS4058 -
Below Ground Inspection chamber -4 Branch, Rectangular door finished externally in a two part grey epoxy coating. For more specifications please see the table below. Code number(s) for available products are: HD4482, HD6482, HD6682 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Below Ground Inspection chamber - 2 Branch, Round door finished externally in a two part grey epoxy coating. Code number(s) for available products are: HD4480, HD6480, HD6680 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Below Ground Inspection chamber -2 Branch, Rectangular door finished externally in a two part grey epoxy coating. Code number(s) for available products are: HD4481, HD6481, HD6681 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008.