-
Above Ground Pipe Taper finished externally in a two part red epoxy coating. For more specifications please see the table below. Code number(s) for available products are: HS3046, HS4046, HS4047, HS6046, HS6047, HS6048, HS8046, HS8047, HS10046, HS10047, HS10048, HS12046, HS12047 & HS12048 Fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Below Ground Pipe Taper finished externally in a two part grey epoxy coating. Code number(s) for available products are: HD6048, HD8046, HD8047, HD10046, HD10047, HD10048, HD12046, HD12047 & HD12048 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Below Ground plain grating. Code number(s) for available products are: HD8077 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Below Ground Puddle Flange finished externally in a two part grey epoxy coating. Code number(s) for available products are: HD4078, HD6078, HD8078, HD10078 & HD12078 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. Bolt on flange is supplied in two halves with stainless steel nuts and bolts. Designed to be bedded on "Denso" tape or similar, wrapped around the pipe to provide a watertight seal. -
Single-piece casting manufactured from Ductile Iron BS EN 1563- Two EPDM sealing gaskets
- Uses the same grub-screw continuity system as proven on our Ductile Iron Couplings
- Meets Hydrostatic test pressures
- Couplings in 2-part epoxy finish to match the applicable system
- Suitable for re-use (Gasket should be checked before re-installation for damage/distortion and replaced if necessary)
-
Single-piece casting manufactured from Ductile Iron BS EN 1563- Two EPDM sealing gaskets
- Uses the same grub-screw continuity system as proven on our Ductile Iron Couplings
- Meets Hydrostatic test pressures
- Couplings in 2-part epoxy finish to match the applicable system
- Suitable for re-use (Gasket should be checked before re-installation for damage/distortion and replaced if necessary)
-
Above Ground Stainless Steel (Grade 430ti) Coupling.- Clamping unit/collar manufactured from ferritic stainless steel AISI 430 Ti
- 50mm – 150mm: M8 zinc plated socket cap screw and nut (6mm Allen Drive)
- 200mm: M10 zinc plated socket cap screw and nut (8mm Allen Drive)
- EPDM synthetic rubber sealing ring
- Block tightening provides visible torque control
- Pressure rated up to 0.5 bar unrestrained
- Quick Fitting
- Suitable for re-use
- Conforms to the requirements of BS EN 877
-
Above Ground Rapid Strut Cantilever Arms. For more specifications please see the table below. Code number(s) for available products are: HSD1846 Fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Above Ground Single Boss Pipe 2" BSPT finished externally in a two part red epoxy coating. For more specifications please see the table below. Code number(s) for available products are: HS3053, HS4053, HS6053 Fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Above Ground Single Compression Fit Boss Pipe finished externally in a two part red epoxy coating. For more specifications please see the table below. Code number(s) for available products are: HS3090, HS4090, HS6090 Fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. -
Below Ground Solid cover. Code number(s) for available products are: HD8076 All our products are fully compliant with BS EN 877:1999 + A1:2006 Incorporating Corrigendum 2008. Supplied with rubber seal and screws fitted. -
Above Ground Stack Support Console With Guidance Clamp. For more specifications please see the table below.- Supplied as standard with guidance clamp illustrated
- EPDM rubber age resistant gaskets
- Sound insulating lining tested DIN4109
|
|
|
|---|
